Key Skills:
• Embedded C , C++ and Assembly Language
• 8 bit, 16 bit & 32 bit MCUs
• Intel, AVR, PIC, Motorola & ARM controller architecture and programming
• Linux , RTOS, Device Drivers
• Communication Protocols - SPI,I2C, USART
• Raspberry Pi , PandaBoard
• Keil, Atmel Studio, MicroC
• Data Acquisition programming (DAQ)
• MATLAB , Delphi Language
• C, C++, C# Language, .NET , Structured query language (SQL)
• PLC- Siemens, AB , Delta PLC programming, Ladder Logic
• SCADA – Intouch, WinCC ,HMI
• AutoCad, MS office, Visio, UML
• Version Control Software -TortoiseHG
• Agile methodology, Development life cycle methodologies
• Analog and digital electronics design
• Microcomputer controlled systems
• Software/algorithm design and development
• Software/hardware QA
Work Experience:
Electrical Engineer, Radyne Corporation, Milwaukee, WI August, 2012 - January 2013[USA],
March 2013 - February 2014[India]
• Assisted in design of the coil used in Induction Heating which included Electrical design and Mechanical design
• Calculated required power, current and voltage for Electrical design and number of turns and diameter for Mechanical Design
• Software development of DAQ device in C# which included real-time graphs of the different parameters
• Performed the code translation from Delphi to C#
• Developed the software which remotely controls the induction power supplies which are connected in the same Ethernet network
Project Engineer (Intern), Anuva Services Inc., Morrisville NC May 2011 – August 2011
• Tested the power supply board at the components level, performed troubleshooting using huntron tracker device & DSO and repaired them
• Installed the server and performed maintenance of workstations & server
• Performed mechanical assembly and pressure sensor calibration & testing of syringe used in breath alcohol ignition interlock device
Group Project, New Jersey Institute of Technology Newark, NJ January 2010 - May 2010
Architecture of a Planetary Space Probe
• Design of fully automatic system which will collect data & images in space and send it to the Earth
• Modules used: Camera, Spectrum Analyzer, Microcontroller, Magnetometer, Gyroscope, JPEG encoder, Battery, Voltage regulator, Sun sensor, Transmitter, Receiver, RAM
Group Project, U V Patel College of Engineering Mehsana, India January 2009 – May 2009
Bionic Hand
• Prosthetic hand based on the use of signals from the brain
• Components used: Instrumentation Amplifier, Band pass filter, Schmitt Trigger, Microcontroller, Driver circuit, Motors
• Assisted with assembly and testing of bionic arm along with the building of algorithm and a firmware, in embedded C & assembly language, to select the proper motor for movement
Group Project, V Patel College of Engineering Mehsana, India
Blood Group Detector using light source & LDR as a detector August 2008 – December 2008
• Approach to determine the blood group by using light source and a detector
• Components used: LED, Photoresistors, Bridge Amplifier, Comparator, Voltage regulator, Microcontroller, 7 segment display
• Assisted with assembly, development of algorithm and firmware ,in embedded C & assembly language, to make the decision and seven segment display of the blood group
Education:
Master of Science Electrical Engineering January 2010 – December 2011
New Jersey Institute of Technology (NJIT) Newark, NJ GPA- 3.25/4.0
• Concentration in Intelligent Systems & Computer Architecture
• Coursework : Project Management, Embedded Computing Systems, Advanced Microprocessor Systems, Computer Systems Architecture, Renewable Energy Systems, Discrete Event Dynamic systems, Computer Network Design & Analysis
Bachelor of Technology Biomedical & Instrumentation Engineering June 2005 to June 2009
U V Patel College of Engineering Mehsana, India GPA- 3.5/4.0
• Coursework : Analog Integrated...
Login or Register to view the full resume.
